This is our journal of what we pray is our sojourn of life (Hebrews 11:8-10) along the narrow way (Matthew 7:14), even the old paths (Jeremiah 6:16), submitting to the Bible as a light unto both (Psalms 119:105). It is our prayer that these documented moments in our earthly time benefit whom God might choose to edify, but ultimately that God glorifies Himself through them.

Goat Milking Stand

When we first started milking our goats, some folks from town graciously gave us a milking stand, and it has served us very well. It has started to really show the effects of time and wear and many repairs, and because when we breed our goats during the winter, we split them into two generations, and so Sue didn’t have to walk goats from one pen to another just for milking, I thought I’d put together another one for her, using the original as a spec.

Thankfully, I was able to scrounge up all of the wood necessary for it, which was nice.

I started with the base, which is basically 2 feet by 4 feet. It might be interesting to make it 3 inches less wide so the cross pieces would be 2 feet instead of 27 inches, but we have quite a few leftover pieces of OSB that were cut out from the 2 foot by 4 foot pony wall windows of the house, so one of those is what I used. The 11 inch legs on the original were something of a weak point, so I tried to bolster them by using 2×4 instead of 2×2, and used screws on both sides (which, to allow for easier replacement, on the long side I did from the inside so the eventually uprights wouldn’t be attached over/covering the leg screws) and the top:

Goat Milking Stand Under Side of Base
Goat Milking Stand Top Side of Base

I then cut out basically all of the parts I would need:

Goat Milking Stand Parts List

The uprights I used an 8 foot 2×6 cut in half to 4 feet, and then ripped at about 1 1/2 inches. Another weak point in the original design was where these uprights attach to the base, so I thought I would shape them at the bottom to hopefully be more sturdy and have more material to which to attach to the base. (UPDATE: please see our goat milking stand update blog post for a continuing problem with this and an enhancement I added.) Note that for many of the screws I drilled pilot holes, especially when dealing with the thinner pieces or older wood:

Goat Milking Stand Uprights

And then I added some cross braces, a 2×4 placed 10 inches from the platform and a ripped in half 2×4 around 3 inches from the top (although I measured from the 2×4 cross brace because the uprights weren’t exactly the same length):

Goat Milking Stand First Cross Braces

And the neck holders, one obviously being only attached at the bottom cross piece (which is the top cross piece because the stand is upside down). These were 3 feet long, ripped from a piece of one of the pieces cut out of the 2×6, a little less than 1 1/2 inches wide so that the moving one would slide nicely between two cross pieces without binding or being too loose. Their outer edges are 9 inches from the outside edge of the cross piece:

Goat Milking Stand Neck Holders

And then the last top cross piece and the shelf holders, which were from a 10 inch 2×4 cut diagonally. Those I put the top level with the top of the bottom 2×4 cross piece:

Goat Milking Stand Back Cross Piece and Feeder Shelf Braces

Here is the shelf. I used a 2×10 for this:

Goat Milking Stand Feeder Shelf

And here are some extra screws I put in to hopefully more securely attach the shelf:

Goat Milking Stand Feeder Shelf Extra Screws

And here it is!

Goat Milking Stand Complete

We had some u-shaped brackets laying around, which just happened to fit perfectly over the two neck holder pieces, and so we’re using that to hold the neck pieces closed when the goat’s neck is in it:

Goat Milking Stand Neck Holders Latch

And here the milking stand is in action! We hope to find and start using something more sturdy for the feed holder instead of plastic buckets, like an aluminum pot or the like from a thrift store — something to withstand the weather and the goats a little better 🙂 :

Goat Milking Stand in Actions

We’re grateful to the Lord for the original stand from those generous town folks, for the left-over wood to be able to use for this, and for the opportunity to have it completed. We are continually thankful for God’s provisions generally and for the healthy goat milk.

— David

6 Comments

  1. Vanja

    Perfect! Well done 🙂
    I always say: "You only want to have goats as long as you don't have them", but you seem to manage just fine 🙂

  2. David and Susan Sifford

    Thanks, Vanja.

    Since we don't dehorn them, they are a little rough on the fences, but seem to do the most damage when they are next to each other in separate pens, where they butt each other through the fence. We have them separated now in far pens for breeding, and don't seem to have much trouble with them that way. They do like to slide along the fencing to scratch themselves — haven't figured out what to do with that yet. 🙂

    It seems as they've got older and been around us more, with Sue milking them all the time, they are all in all pretty tame, for which we're thankful.

    Thanks for saying hello!

    — David

  3. Anonymous

    Thanks for this. I will probably be building one of these soon, DV. Thank you for your blog, I read it all the time. I just haven't been commenting as often.
    – Todd in Oregon

  4. David and Susan Sifford

    Hi Todd,

    We just pray the Lord glorifies Himself with the blog. Thanks for saying hello.

    — David

  5. Unknown

    David,

    I have found with my meat goats I have been able to stop them from scratching, and there by pushing their fence down, by placing 1 strand of barbed wire about knee high in the fence.

    Thanks for the enjoyable blog.

    GR

  6. David and Susan Sifford

    Hi GR,

    I was looking at the fences I believe just the other day wondering what could be done to help with that. Very good! Thanks much for taking the time to offer that info.

    — David

Leave a Reply

Your email address will not be published. Required fields are marked *

15 − one =